The starter motor is an electric motor that turns over or "cranks" the engine to start. It consists of a powerful DC (Direct Current) electric motor and the starter solenoid that is attached to the motor.
 |
| A starter motor |
In most cars, a starter motor is bolted to the engine or transmission.
The starter motor is powered by the car's main 12-volt battery. To turn over the engine, the starter motor requires a very high electric current, which means the battery must have sufficient power. If the battery is discharged, the lights in a car might come on, but it won't be enough power (current) to turn over the starter motor.
Symptoms of A Bad Starter Motor.
When starting a car with a fully charged battery, there is a single click, or nothing happens at all. The starter motor doesn't run, even though there is a 12-Volt power at the starter control terminal.
Another symptom is when the starter motor runs but fails to turn over the engine. Often, this might cause a loud screeching noise when starting the car. Of course, this could also be caused by damaged teeth on the ring gear of the flex plate or flywheel.
Starter Solenoid
 |
| A starter solenoid |
A typical starter solenoid has one small connector for the starter control wire (the white connector in the photo) and two large terminals: one for the positive battery cable and the other for the thick wire that powers the starter motor itself.
 |
| A starting system |
The starter solenoid works as a powerful electric relay. When activated, through the control terminal, the solenoid closes the hi-current electric circuit and sends the battery power to the starter motor. At the same time, the starter solenoid pushes the starter gear forward to mesh with the ring gear of the engine flexplate or flywheel.
Battery Cables
The starter motor requires a very high electric current to turn over the engine, that's why it's connected to the battery with thick (large gauge) cables.
The negative (ground) cable connects the negative "-" battery terminal to the engine cylinder block, or transmission, close to the starter. The positive cable connects the positive "+" battery terminal to the starter solenoid.
A poor connection at one of the battery cables can cause the starter motor not to run.
How The Starting System Works:
When you turn the ignition key to the START position, or press the START button, if the transmission is in Park or Neutral, the battery voltage goes through the starter control circuit and activates the starter solenoid. The starter solenoid powers the starter motor. At the same time, the starter solenoid pushes the starter gear forward to mesh it with the engine flywheel (flexplate in an automatic transmission). The flywheel is attached to the engine crankshaft. The starter motor spins, turning over the engine crankshaft allowing the engine to start. In cars with a push button start, the system disengages the starter as soon as the engine starts running.
Neutral Safety Switch
For safety reasons, the starter motor can only be operated when the automatic transmission is in Park or Neutral position; or if the car has a manual transmission, when the clutch pedal is depressed (not all manual cars). In vehicles with a manual transmission, the clutch pedal switch completes the starter motor circuit when pressed. In cars with an automatic transmission, the transmission range switch allows the starter to operate only when a transmission is in Park or Neutral.
The job of the transmission range switch is to tell the vehicle computer (Power Control Module PCM aka brain box) which gear the transmission is in.
If your car has a gear indicator on the dash, you might be able to see when a transmission range indicator is not working. The most common problem is when you shift the transmission into "Park" and the letter "P" doesn't show on the dash. This means that the vehicle computer (PCM) doesn't know that the transmission is in "Park" and will not allow the starter to operate. The symptom of this problem is when the vehicle starts in Neutral, but doesn't start in "Park".
 |
| A neutral safety switch |
This problem is often caused by a corroded or seized cable, or cable lever. The rust at restricts the cable movement and prevents the switch from working properly. The solution is to lubricate the cable connection point and, if needed, replace rusted parts. The transmission range switch position might need to be readjusted too.
Starting System Problems
Starting system problems are common and not all of them are caused by a faulty starter motor. If when you are trying to start the car, you hear that the starter cranks as usual, but the car doesn't start, then the problem is most likely not with the starting system. Here are a few common starting system problems:
The battery is very common to fail. Sometimes one of the electrical components (parking lights, map lights etc.) that was left on or has a defect causing parasitic current draw drains the battery. Sometimes, an old battery can just die one day, with no warning. In either case, if the battery is low on charge, it won't have enough power for the starter motor to turn over the engine.
If the battery is low on charge, when attempting to start the engine you might hear a single click or repeated clicking, or the starter may turn over slowly and stop.
Poor connection at the cable terminals can cause the starter not to work or run very slow too. Often the battery terminals or the ground cable connection get corroded causing starter problems
 |
| Battery terminals |
Sometimes the starter control terminal gets corroded, or a starter control wire gets loose or disconnected from the terminal causing the starter not to work.
 |
| Corroded starter terminals |
The starter motor itself could fail. Sometimes the carbon brushes or some other parts inside the starter motor wear out and the starter motor stops working. If the starter motor is faulty, it may have to be replaced. Rebuilding the starter motor is usually cheaper but takes more time.
Sometimes the starter gear for some reason won't mesh properly with the engine flywheel. This may cause a very loud metal grinding or screeching sound when attempting to start the car. In this case, the flywheel ring gear needs to be checked for damaged teeth. This is not very common.
An ignition could fail as well. The contact points inside the ignition switch wear out, so when you turn the ignition switch to the "Start" position, no electric current is going through the starter control circuit to activate the starter solenoid. If jiggling the key in the ignition helps start the car, it's possible that the ignition switch is defective.
A neutral safety switch can also fail or get out of adjustment. For example, if a car starts in "Neutral" but doesn't start in "Park," the neutral safety switch should be checked first.
Just start from the simple stuff and work your way up.
How A Starter Motor Works
 |
| The components of a starter motor |
The starter motor typically has four field windings (field coils) attached to the starter motor housing from the inside. The armature (the rotating part) is connected through the carbon brushes in series with the field coils. On the front end of the armature, there is a small gear that is attached to the armature through an overrunning clutch.
When the driver turns the key or presses the Start button, the solenoid winding is energized. The solenoid plunger moves in the direction of the arrow and closes the solenoid contacts. This connects the battery power to the starter motor (field coils and armature). At the same time, the plunger pushes the starter gear forward through the lever. The gear then engages with the ring gear of the flexplate and turns it over. The flexplate is attached to the engine crankshaft.
 |
| A starter motor |
Most of the starter problems are caused by worn out or burned solenoid contacts, worn brushes and a commutator and worn armature bushings. The symptom of worn out solenoid contacts is when the solenoid clicks but the starter motor doesn't run. When the starter brushes are worn out, the starter motor doesn't make any noises. When front and rear armature bushings wear out, the armature rubs against the field shoes causing the starter motor to run slow and noisy. Many modern starter motors have small ball bearings instead of the bushings.
Twitter and Instagram; @VverteAutoSevcs
Email; vverteautosevcs@gmail.com
Phone; 09137103730
<script async src="https://pagead2.googlesyndication.com/pagead/js/adsbygoogle.js?client=ca-pub-2583627563363777"
crossorigin="anonymous"></script>
www.samarins.com
Comments
Post a Comment